Monel K-500 Nickel alloy

Monel K500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel K500 with the added advantage of greater strength and hardness. These amplified properties, strength and hardness, are obtained by adding aluminum and titanium to the nickel-copper base and by a thermal processing used to effect precipitation, typically called age hardening or aging. When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Monel K-500 has approximately three times the yield strength and double the tensile strength when compared with Monel 400. Plus, it can be further strengthened by cold working prior to precipitation hardening. The strength of this nickel steel alloy is maintained to 1200°F but stays ductile and tough down to temperatures of 400° F. Its melting range is 2400-2460°F.
Monel K500 Nickel alloy similar material are : UNS N05500,Alloy K500
Monel K-500 Nickel alloy usually used in the following industries :
Sour-gas service applications
Oil and gas production safety lifts and valves
Oil-well tools and instruments like drill collars
Oil well industry
Doctor blades and scrapers
Chains, cables, springs, valve trim, fasteners for marine service
Pump shafts and impellers in marine service

Monel K-500 Nickel alloy
Chemical Composition, % of Monel K-500 Nickel alloy

Ni Cu Al Ti C Mn Fe S Si
63.0-70.0 Remainder 2.30-3.15 0.35-0.85 0.25 max 1.5 max 2.0 max 0.01 max 0.50 max

Mechanical Properties of Monel K-500

Product Form Condition Tensile (ksi) .2%Yield (ksi) Elongation % Hardness
Rod & Bar Hot-Finished/Aged 140-190 100-150 30-20 27-38HRC
Rod & Bar Hot Finished/Annealed 90-110 40-60 45-25 75-90 HRB
Rod & Bar Hot Finished/Annealed/Aged 130-165 85-120 35-20 24-35 HRC
Rod & Bar Cold-Drawn/Aged 135-185 95-160 30-15 25-41 HRC
Rod & Bar Cold-Drawn/Annealed/Aged 130-190 85-120 30-20 24-35 HRC
Plate Hot-Finished/Aged 140-180 100-135 30-20 27-37 HRC
Sheet Cold-Rolled/Annealed 90-105 40-65 45-25 85 HRB Ma

Monel K500 Product form and Specifications:

Bar Rod
AMS 4676 AMS 4676

Monel 400 steel

Monel 400 is a nickel-copper alloy (about 67% Ni – 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Monel 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.
Monel 400 Nickel alloy similar material are : UNS N04400, NiCu30Fe
Monel 400 Nickel alloy usually used in the following industries :
Marine engineering
Chemical and hydrocarbon processing equipment
Gasoline and freshwater tanks
Crude petroleum stills
De-aerating heaters
Boiler feed water heaters and other heat exchangers
Valves, pumps, shafts, fittings, and fasteners
Industrial heat exchangers
Chlorinated solvents
Crude oil distillation towers

Monel 400 steel

Monel 400 Nickel base alloy Chemical composition:

Ni Cr C Mn Si Mo Cu Co Al Ti
38-46 19.5-23.5 ≤0.025 ≤1.0 ≤0.5 2.5-3.5 1.5-3.0 ≤1.0 ≤0.2 0.6-1.2

Monel 400 Nickel base alloy Mechanical Properties (Typical room temperature Tensile Properties of Annealed Material)

Product Form Condition Tensile (ksi) .2% Yield (ksi) Elongation (%) Hardness (HRB)
Rod & Bar Annealed 75-90 25-50 60-35 60-80
Rod & Bar Cold-Drawn StressRelieved 84-120 55-100 40-22 85-20 HRC
Plate Annealed 70-85 28-50 50-35 60-76
Sheet Annealed 70-85 30-45 45-35 65-80
Tube&Pipe Seamless Annealed 70-85 25-45 50-35 75 max *

Monel 400 Nickel base alloy Product form and Specifications:

Product

ASTM
Pipe Seamless B165
Pipe Welded B725
Tube Seamless B163
Sheet/Plate B127
Ring/Bar/Rod B164
Forging B564
Fitting B366

Monel alloy steel

Monel is a nickel metal matrix other alloying elements copper, iron, manganese, etc. made. Monel good corrosion resistance, silvery white, suitable for edge wire material.

Monel alloy steel
Application:
Monel alloy is mainly used for the shaft, stem, conveyor scrapers, oil well drilling rings, elastic components, valve pad, etc., applicable to the petroleum, chemical, shipbuilding, pharmaceutical, electronics department.
1. The power plant of seamless pipes, steam pipes
2. seawater exchangers and evaporators
3. sulfuric acid and hydrochloric acid environment
4. Crude Distillation
5. deep-sea equipment used and the propeller shaft
6. The nuclear industry for the manufacture and extraction of uranium isotope separation equipment
7. hydrochloric acid manufacturing equipment used in pumps and valves
Production specification:
steel plate: Thickness:0.5mm-15mm; Length:2500mm;Width:1200mm;
Thickness:1mm5-110mm Length:<1000mm.
Belt:Thickness:0.5mm – 3mm, Width:<300mm;
Standard: ASTM B164 (bar, wire), ASTM B564 (forging), ASTM B127 (sheet, strip), ASTM B165 (seamless pipe).