Inconel 690 alloy steel

Inconel 690 alloy is on the base is of Inconel 600 alloy, the chromium content increased to 30%, a new type of evaporator carbon content below 0.04% and the development of nickel base corrosion resistant alloy. It not only has excellent resistance to stress corrosion cracking ability, but also has high strength, good stability and excellent metallurgical processing capability. Characteristics, has been widely used in PWR nuclear power plant on the evaporator tube.
Inconel 690 alloy similar material are:UNS N06690
Inconel 690 alloy chief application:
Inconel 690 alloy is mainly used for the material of nuclear power plant steam generator tubes in pressurized water reactor.

Inconel 690 alloy steel

Chemical Composition, % of Inconel 690 alloy steel

Ni Cr Fe C Al Ti Mn Si Cu P S
Balance 30.39 8.88 0.023 0.22 0.26 0.23 0.07 0.02 0.006 0.002

physical property of Inconel 690 alloy steel

Yield strength Tensile strength Elongation
350MPa 700MPa 45%

Inconel 690 alloy mechanical property:
Inconel 690 density : 8.19g/cm
Inconel 690 melting point: 1343-1377 degree
Inconel 690 alloy steel Existence of main products:
Forging, bar, sheet, strip, ring, wire, bolts, spring
Inconel 690 alloy steel Mechanical Properties:
Inconel 690 has high strength over a broad range of temperatures. Mechanical properties of the alloy vary with product form and temper. Alloy 690 is normally used in the annealed temper, and strength characteristics described below are representative of annealed material. The usual annealing temperature is approximately 1900°F (1040°C).

Inconel 601 Product form and Specifications:

Product ASTM ASME
Pipe Seamless B167 SB167
Tube Seamless B167 SB167
Sheet/Plate B168 SB168
Ring/Bar/Rod B166 SB166
Fitting B366 SB366

Monel K500 , NO5500

Monel K500 , NO5500 steel Features: good mechanical properties, has a more curved than MONEL 400 strength and hardness.

Monel K500 , NO5500

Chemical composition of Monel K500,NO5500

Product Ni Fe C Si Mn Cu S
Monel K500 Ni65Cu30Al 66.5 1.25 0.13 0.25~1.6 0.75 29.5 0.008

Mechanical behavior of Monel steel K500,NO5500

Grade Temperature ℃ Tensile strength σbMPa Elongation δ5(%) Hardness ( HB)
Monel K500 (cold drawn state) -79 780 39 /
Monel K500 (forging state) -253 1120 50 260-350
Monel K500 (annealed) Room temperature 620-720 25-45 150-190
Monel K500 (thermal processing state) Room temperature 620-1090 20-45 190-330
Monel K500 (cold drawn state) Room temperature 730-990 15-40 190-280
Monel K500 thermal processing aging 300 1020 45 /
Monel K500 thermal processing aging 400 910 25 /

Monel K500 , NO5500 steel application : Fasteners, structural parts widely used stone chemical, petrochemical, ship and marine engineering used in.
Resistance to chloride induced stress corrosion cracking
High resistance to alkalis
Monel 405 Nickel base alloy forms Available:
Round Bar (ASTM specification B 164)
Hex Bar

Monel 405 alloy steel

Monel 405 steel material is the free machining version of Monel 405. It is a nickel-copper alloy with a controlled amount of sulfur added to provide sulfide inclusions that act as chip breakers during machining. Like Monel 405, alloy Monel 405 is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Monel 405 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion-resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions. This nickel steel alloy is particularly resistant to hydrochloric and hydrofluoric acidswhenthey are de-aerated. As would be expected from its high copper content, alloy Monel 405 is rapidly attacked by nitric acid and ammonia systems.
Monel 405 Nickel alloy usually used in the following industries :UNS N04405
Monel 405 is chiefly used for automatic-screw-machine stock and it not generally recommended for other applications. Screw machine stock for fasteners and similar high production run items.
Meter and valve parts
Fasteners
Screw machine products

Monel 405 alloy steel

Chemical Composition, % of Monel 405 Nickel base alloy

Ni Cu Fe S Mn C Si
63.0 min 28.0-34.0 2.5 max 0.025-0.060 2.0 max 0.3 max 0.5 max

Mechanical Properties of Monel 405 Nickel base alloy

Condition Tensile (ksi) .2% Yield (ksi) Elongation % Hardness Brinell (3000 kg) Hardness Rockwell B
Annealed 70-85 25-40 50-35 110-140 60-76
Hot-Finished 75-90 35-60 45-30 130-170 72-86
Cold-Drawn, As-Drawn 85-115 50-105 35-15 160-245 85-23C

Monel 405 Nickel base alloy characteristics :
Characteristics are essentially the same as those of Monel 400 such as:
Good machinability and is recommended for use with automatic screw machines
Resistant to seawater and steam at high temperatures
Excellent resistance to rapidly flowing brackish water or seawater
Excellent resistance to stress corrosion cracking in most freshwaters
Particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated
Offers some resistance to hydrochloric and sulfuric acids a modest temperatures and concentrations, but is seldom the material of choice for these acids
Excellent resistance to neutral and alkaline salt
Resistance to chloride induced stress corrosion cracking
High resistance to alkalis

Monel 400 alloy steel

Monel 400 is a nickel-copper alloy steel (about 67% Ni – 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Monel 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.
Monel 400 Nickel alloy similar material are : UNS N04400, NiCu30Fe
Monel 400 Nickel alloy usually used in the following industries :
Marine engineering
Chemical and hydrocarbon processing equipment
Gasoline and freshwater tanks
Crude petroleum stills
De-aerating heaters
Boiler feed water heaters and other heat exchangers
Valves, pumps, shafts, fittings, and fasteners
Industrial heat exchangers
Chlorinated solvents
Crude oil distillation towers

Monel 400 alloy steel

Chemical composition of Monel 400 alloy steel

Ni Cr C Mn Si Mo Cu Co Al Ti
38-46 19.5-23.5 ≤0.025 ≤1.0 ≤0.5 2.5-3.5 1.5-3.0 ≤1.0 ≤0.2 0.6-1.2

Mechanical Properties of Monel 400 Nickel base alloy

Product Form Condition Tensile (ksi) .2% Yield (ksi) Elongation (%) Hardness (HRB)
Rod & Bar Annealed 75-90 25-50 60-35 60-80
Rod & Bar Cold-Drawn StressRelieved 84-120 55-100 40-22 85-20 HRC
Plate Annealed 70-85 28-50 50-35 60-76
Sheet Annealed 70-85 30-45 45-35 65-80
Tube&Pipe Seamless Annealed 70-85 25-45 50-35 75 max *

Monel 400 Nickel base alloy Product form and Specifications:

Product ASTM
Pipe Seamless B165
Pipe Welded B725
Tube Seamless B163
Sheet/Plate B127
Ring/Bar/Rod B164
Forging B564
Fitting B366

 

Monel K-500 Nickel alloy

Monel K500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel K500 with the added advantage of greater strength and hardness. These amplified properties, strength and hardness, are obtained by adding aluminum and titanium to the nickel-copper base and by a thermal processing used to effect precipitation, typically called age hardening or aging. When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Monel K-500 has approximately three times the yield strength and double the tensile strength when compared with Monel 400. Plus, it can be further strengthened by cold working prior to precipitation hardening. The strength of this nickel steel alloy is maintained to 1200°F but stays ductile and tough down to temperatures of 400° F. Its melting range is 2400-2460°F.
Monel K500 Nickel alloy similar material are : UNS N05500,Alloy K500
Monel K-500 Nickel alloy usually used in the following industries :
Sour-gas service applications
Oil and gas production safety lifts and valves
Oil-well tools and instruments like drill collars
Oil well industry
Doctor blades and scrapers
Chains, cables, springs, valve trim, fasteners for marine service
Pump shafts and impellers in marine service

Monel K-500 Nickel alloy
Chemical Composition, % of Monel K-500 Nickel alloy

Ni Cu Al Ti C Mn Fe S Si
63.0-70.0 Remainder 2.30-3.15 0.35-0.85 0.25 max 1.5 max 2.0 max 0.01 max 0.50 max

Mechanical Properties of Monel K-500

Product Form Condition Tensile (ksi) .2%Yield (ksi) Elongation % Hardness
Rod & Bar Hot-Finished/Aged 140-190 100-150 30-20 27-38HRC
Rod & Bar Hot Finished/Annealed 90-110 40-60 45-25 75-90 HRB
Rod & Bar Hot Finished/Annealed/Aged 130-165 85-120 35-20 24-35 HRC
Rod & Bar Cold-Drawn/Aged 135-185 95-160 30-15 25-41 HRC
Rod & Bar Cold-Drawn/Annealed/Aged 130-190 85-120 30-20 24-35 HRC
Plate Hot-Finished/Aged 140-180 100-135 30-20 27-37 HRC
Sheet Cold-Rolled/Annealed 90-105 40-65 45-25 85 HRB Ma

Monel K500 Product form and Specifications:

Bar Rod
AMS 4676 AMS 4676

Monel 400 steel

Monel 400 is a nickel-copper alloy (about 67% Ni – 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Monel 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.
Monel 400 Nickel alloy similar material are : UNS N04400, NiCu30Fe
Monel 400 Nickel alloy usually used in the following industries :
Marine engineering
Chemical and hydrocarbon processing equipment
Gasoline and freshwater tanks
Crude petroleum stills
De-aerating heaters
Boiler feed water heaters and other heat exchangers
Valves, pumps, shafts, fittings, and fasteners
Industrial heat exchangers
Chlorinated solvents
Crude oil distillation towers

Monel 400 steel

Monel 400 Nickel base alloy Chemical composition:

Ni Cr C Mn Si Mo Cu Co Al Ti
38-46 19.5-23.5 ≤0.025 ≤1.0 ≤0.5 2.5-3.5 1.5-3.0 ≤1.0 ≤0.2 0.6-1.2

Monel 400 Nickel base alloy Mechanical Properties (Typical room temperature Tensile Properties of Annealed Material)

Product Form Condition Tensile (ksi) .2% Yield (ksi) Elongation (%) Hardness (HRB)
Rod & Bar Annealed 75-90 25-50 60-35 60-80
Rod & Bar Cold-Drawn StressRelieved 84-120 55-100 40-22 85-20 HRC
Plate Annealed 70-85 28-50 50-35 60-76
Sheet Annealed 70-85 30-45 45-35 65-80
Tube&Pipe Seamless Annealed 70-85 25-45 50-35 75 max *

Monel 400 Nickel base alloy Product form and Specifications:

Product

ASTM
Pipe Seamless B165
Pipe Welded B725
Tube Seamless B163
Sheet/Plate B127
Ring/Bar/Rod B164
Forging B564
Fitting B366

Inconel 690 steel

Inconel 690 alloy is on the base is of Inconel 600 alloy, the chromium content increased to 30%, a new type of evaporator carbon content below 0.04% and the development of nickel base corrosion resistant alloy. It not only has excellent resistance to stress corrosion cracking ability, but also has high strength, good stability and excellent metallurgical processing capability. Characteristics, has been widely used in PWR nuclear power plant on the evaporator tube.
Inconel 690 alloy similar material are:UNS N06690
Inconel 690 alloy chief application:
Inconel 690 alloy is mainly used for the material of nuclear power plant steam generator tubes in pressurized water reactor.

Inconel 690 steel
Inconel 690 alloy steel Chemical Composition, %

Ni Cr Fe C Al Ti Mn Si Cu P S
Balance 30.39 8.88 0.023 0.22 0.26 0.23 0.07 0.02 0.006 0.002

Inconel 690 alloy steel physical property :

Yield strength Tensile strength Elongation
350MPa 700MPa 45%

 

Monel alloy steel

Monel is a nickel metal matrix other alloying elements copper, iron, manganese, etc. made. Monel good corrosion resistance, silvery white, suitable for edge wire material.

Monel alloy steel
Application:
Monel alloy is mainly used for the shaft, stem, conveyor scrapers, oil well drilling rings, elastic components, valve pad, etc., applicable to the petroleum, chemical, shipbuilding, pharmaceutical, electronics department.
1. The power plant of seamless pipes, steam pipes
2. seawater exchangers and evaporators
3. sulfuric acid and hydrochloric acid environment
4. Crude Distillation
5. deep-sea equipment used and the propeller shaft
6. The nuclear industry for the manufacture and extraction of uranium isotope separation equipment
7. hydrochloric acid manufacturing equipment used in pumps and valves
Production specification:
steel plate: Thickness:0.5mm-15mm; Length:2500mm;Width:1200mm;
Thickness:1mm5-110mm Length:<1000mm.
Belt:Thickness:0.5mm – 3mm, Width:<300mm;
Standard: ASTM B164 (bar, wire), ASTM B564 (forging), ASTM B127 (sheet, strip), ASTM B165 (seamless pipe).

About Us

Henan Supioneer Metal Materials Co., Ltd (SDJS) is the only steel supplier in China who
provides the most comprehensive types of steel. Our steel plate products include black
steel plates, stainless steel plates, galvanized steel plates, checkered steel plates,
steel coils and so on. Among all steel plate products of our company, extra wide and thick
steel plates, CrMo steel plates, low temperature pressure vessel steel plates, and high
strength steel plates are the four featured products. Supioneer Metal Materials Co., Ltd
has established longterm strategic cooperative relationships with the producers of the
products mentioned above. Powerful product sources and marketing capacity enable us to take
the leading place in domestic steel trade. Now the company has shifted its focus to the
exportation of steel materials, and our aim is to become the largest and strongest steel
materials supplier in China’s international trade.

We can provide ExtraWide and Extrathick Steel Plate with max thickness of 700mm, max piece
weight of 50t, which makes us the only supplier of China who can provide steel plate of
such specification. Anti Hydrogen CrMo Steel Plate with max thickness of 198mm and max
piece weight of 38t is also available. Our Low Temperature Pressure Vessel Steel Plate is
weldable under the temperature condition of -196℃. Representative steel grades of low
temperature vessel steel plate are 9Ni (SA553),08NiDR (SA203E), all with better properties
compared to international quality standards. We can also provide High Strength Steel Plate
with excellent quality.

The company embraces all kinds of steel plate material products. Product standard grades
cover main international standards for steel materials, such as ASTM, ASME, API, JIS, DIN,
BS, etc., and these products are sold across over 100 countries and areas in Middle east,
Southeast Asia, Africa, South America, etc. We now have four large scale warehouses for
abundant product supply: one is located in Shanghai and has a stock inventory of about 7,
000 tons; the warehouse in Qingdao has a stock inventory of about 6, 500 tons; and each
warehouse in Tianjin and Zhengzhou has about 3, 000 tons of stock inventory. Based on the
sound foundation of steel resources, Supioneer Metal Materials Co., Ltd also adopts the
“one stop” service, allowing customers to enjoy the lowest cost for steel cutting, welding,
drilling, galvanizing, and the best quality service at the same time.